Étude des potentialités des systèmes d’application contrôlée des gouttes (CDA) pour les traitements phytosanitaires en céréaliculture (synthèse bibliographique)
Ouled Taleb Salah, Sofiene; De Cock, Nicolas; Massinon, Mathieuet al.
2016 • In Biotechnologie, Agronomie, Société et Environnement
Application des pesticides, pulvérisateur, buse, adjuvant, rétention, dérive
Abstract :
[fr] Introduction. L’application contrôlée des gouttes (CDA) présente le double avantage de réduire à la fois l’étendue de la
distribution des tailles des gouttes et le volume appliqué par rapport aux buses hydrauliques conventionnelles.
Littérature. Cette revue investigue la potentialité de la CDA par rapport aux buses hydrauliques dans le cadre du désherbage
précoce des adventices (2-3 feuilles). En termes de rétention, les études reliant les caractéristiques des gouttes (taille, vitesse
et direction) et l’architecture, la densité et la mouillabilité du feuillage, en fonction de la formulation de bouillies, ont été
abordées. Ces études montrent que des gouttes de 300 μm avec un adjuvant approprié et des jets émis 60° vers l’avant par
rapport à la verticale contribuent à l’augmentation de la rétention sur les cibles problématiques à port dressé. L’effet des
réductions des volumes d’application pour ces deux techniques est étudié sur base de la moyenne, du coefficient de variation et
du taux de couverture des dépôts. Néanmoins, les résultats de ces études ne peuvent être généralisés du fait des différences de
réglages opératoires entre les deux techniques d’application. Quant à la dérive, les atomiseurs CDA orientés horizontalement
présentent un potentiel de dérive plus important que les buses hydrauliques pour lesquelles le spray est orienté vers le bas. La
dérive augmente avec la vitesse du vent et diminue lorsque le diamètre médian volumétrique (DV50) augmente.
Conclusions. De nouveaux réglages des atomiseurs de la CDA en termes de DV50 et de direction du jet peuvent répondre
aux défis de l’agriculture de précision. Les pistes d’innovations proposées sont d’une part une amélioration de la résistance à
l’usure des dents situées en bordure des disques et, d’autre part, une distribution granulométrique plus étroite.
Disciplines :
Agriculture & agronomy
Author, co-author :
Ouled Taleb Salah, Sofiene ; Université de Liège > Ingénierie des biosystèmes (Biose) > Agriculture de précision
De Cock, Nicolas ; Université de Liège > Ingénierie des biosystèmes (Biose) > Agriculture de précision
Massinon, Mathieu ; Université de Liège > Ingénierie des biosystèmes (Biose) > Agriculture de précision
Schiffers, Bruno ; Université de Liège > Agronomie, Bio-ingénierie et Chimie (AgroBioChem) > Analyse, qual. et risques - Labo. de Chimie analytique
Dorbolo, Stéphane ; Université de Liège > Département de physique > Physique statistique
Lebeau, Frédéric ; Université de Liège > Ingénierie des biosystèmes (Biose) > Agriculture de précision
Language :
French
Title :
Étude des potentialités des systèmes d’application contrôlée des gouttes (CDA) pour les traitements phytosanitaires en céréaliculture (synthèse bibliographique)
Alternative titles :
[en] Study of the potential for the use of controlled droplet application (CDA) upon cereal crops. A review [en] Study of the potential for the use of controlled droplet application (CDA) upon cereal crops. A review
Publication date :
2016
Journal title :
Biotechnologie, Agronomie, Société et Environnement
ISSN :
1370-6233
eISSN :
1780-4507
Publisher :
Presses Agronomiques de Gembloux, Gembloux, Belgium
Al Heidary, M., Douzals, J.P., Sinfort, C., Vallet, A., Influence of spray characteristics on potential spray drift of field crop sprayers: A literature review (2014) Crop Prot., 63, pp. 120-130
Baetens, K., A validated 2-D diffusion-advection model for prediction of drift from ground boom sprayers (2009) Atmos. Environ., 43, pp. 1674-1682
Bédiaf, H., Sabre, R., Journaux, L., Cointault, F., Comparison of leaf surface roughness analysis methods by sensitivity to noise analysis (2015) Biosyst. Eng., 136, pp. 77-86
Bode, L.E., Zimmerman, T.L., Goering, C.E., Gebhardt, M.R., The effects of flow rate on the distribution pattern and drop-size spectrum of a spinning atomizer (1972) Trans. ASAE, 15, pp. 86-90
Bode, L.E., Butler, B.J., Pearson, S.L., Bouse, L.F., Characteristics of the micromax rotary atomizer (1983) Trans. ASAE, 26, pp. 999-1005
Bouchet, C., Pulvérisation à volume réduit et bas volume en grandes cultures. Résultats de trois années d’experimentation (1982) EPPO Bull., 13 (3), pp. 547-554
Boukhalfa, H.H., Massinon, M., Belhamra, M., Lebeau, F., Contribution of spray droplet pinning fragmentation to canopy retention (2014) Crop Prot., 56, pp. 91-97
Butler Ellis, M.C., Webb, D.A., Western, N.M., The effect of different spray liquids on the foliar retention of agricultural sprays by wheat plants in a canopy (2004) Pest Manage. Sci., 60, pp. 786-794
Butler Ellis, M.C., Knight, S., Miller, P.C.H., (2007) Spray Behaviour and Efficacy of Herbicides and Fungicides Applied to Wheat at Reduced Volumes. HGCA Project Report 408, , Kenilworth, UK: Agriculture and Horticulture Development Board Cereals & Oilseeds
Butler Ellis, M.C., Lane, A.G., O’Sullivan, C.M., (2014) Distribution of Spray Applied to a Cereal Crop and the Effect of Application Parameters on Penetration. HGCA Project Report 526, , Kenilworth, UK: Agriculture and Horticulture Development Board Cereals & Oilseeds
Clayton, J., A new generation hand held spinning disc sprayer: The micron ulva+ for small farmer crop protection (1992) Proceedings of the IRCT Cotton Conference, , February 1992, N’Djamena, Chad
Clayton, J.S., Bals, T.E., Povey, G.S., A new generation hand-held ulva sprayer (1993) Proceedings of the 2Nd International Symposium on Pesticide Application Techniques, , 22-24 September 1993, Strasbourg, France
Cox, S.J., Salt, D.W., Lee, B.E., Ford, M.G., A model for the capture of aerially sprayed pesticide by barley (2000) J. Wind Eng. Ind. Aerodyn., 87, pp. 217-230
Derksen, R.C., Bode, L.E., Droplet size comparisons from rotary atomisers (1986) Trans. ASAE, 29, pp. 1204-1207
Doble, S.J., Matthews, G.A., Rutherford, I., Southcombe, E.S.E., A system for classifying hydraulic and other atomisers into categories of spray quality (1985) Proceedings of the Brighton Crop Protection Conference - Weeds, pp. 1125-1133. , 18-21 November, 1985, Brighton Metropole, England, British Crop Protection Enterprises
Dombrowski, N., Lloyd, T.L., Air drag on ligaments produced from rotating cups (1973) J. Chem. Eng. Jpn., 6 (4), pp. 363-365
Dombrowski, N., Lloyd, T.L., Atomisation of liquids by spinning cups (1974) Chem. Eng. J., 8, pp. 63-81
Elbanna, H., Rashed, M.J.I., Ghazi, M.A., Droplets from liquid sheets in an air stream (1984) Trans. ASAE, 27, pp. 677-679
Forster, W.A., Kimberley, M.O., Zabkiewicz, J.A., A universal spray droplet adhesion model (2005) Trans. ASAE, 48 (4), pp. 1321-1330
Frost, A.R., Rotary atomization in the ligament formation mode (1981) J. Agric. Eng. Res., 26, pp. 63-78
Gebhardt, M.R., Rotary disk atomisation (1988) Weed Technol., 2, pp. 106-113
Gil, Y., Sinfort, C., Emission of pesticides to the air during sprayer application: A bibliographic review (2005) Atmos. Environ., 39, pp. 5183-5193
Goering, C.E., Foster, R.A., Bode, L.E., Gebhardt, M.R., Development of a shielded, spinning disk atomizer (1972) Trans. ASAE, 15 (5), pp. 814-817
Hewitt, A.J., Valcore, D.L., Teske, M.E., Schick, R.J., Drop size classifications for agricultural sprays (1998) Proceedings of the 11Th Annual Conference on Liquid Atomization and Spray Systems, , May 1998, Sacramento, CA, USA
Hoffmann, W.C., Kirk, I.W., Spray deposition and drift from two “medium” nozzles (2005) Trans. ASAE, 48 (1), pp. 5-11
Holland, J.M., Jepson, P.C., Jones, E.C., Turner, C., A comparison of spinning disc atomisers and flat fan pressure nozzles in terms of pesticide deposition and biological efficacy within cereal crops (1997) Crop Prot., 16, pp. 179-185
Jensen, P.K., Increasing efficacy of graminicides with a forward angled spray (2012) Crop Prot., 32, pp. 17-23
Knoche, M., Effect of droplet size and carrier volume on performance of foliage-applied herbicides (1994) Crop Prot., 13, pp. 163-178
Massinon, M., Boukhalfa, H.H., Marechal, P., Lebeau, F., The effect of leaf orientation on spray retention on blackgrass (2012) Proceedings of the 11Th International Conference on Precision Agriculture, , 15-18 July 2012, Hyatt Regency, Indianapolis, USA
Massinon, M., Lebeau, F., Comparison of spray retention on synthetic superhydrophobic surface with retention on outdoor grown wheat leaves (2012) Proceedings of the International Advances in Pesticide Application: Aspects of Applied Biology 114, pp. 261-268. , 11 January 2012, Hof Wageningen, The Netherlands. Warwick, UK: Association of Applied Biologists
Massinon, M., Lebeau, F., Review of physicochemical processes involved in agrochemical spray retention (2013) Biotechnol. Agron. Soc. Environ., 17, pp. 494-504
Massinon, M., Evaluation of process-driven spray retention model on early growth stage barley (2014) Proceedings of the International Conference of Agricultural Engineering, , 6-10 July 2014, Zurich, Switzerland
Massinon, M., Study of retention variability on an early growth stage herbaceous plant using a 3D virtual spraying model (2015) Crop Prot., 78, pp. 63-71
Morel, M., Pulvérisation centrifuge à très bas volume: TG 412 (1982) EPPO Bull., 13 (3), pp. 363-364
Nuyttens, D., Influence of nozzle type and size on drift potential by means of different wind tunnel evaluation methods (2009) Biosyst. Eng., 103, pp. 271-280
Ozkan, H.E., Shields to reduce spray drift (1997) J. Agric. Eng. Res., 67, pp. 311-322
Qi, L., Miller, P.C.H., Fu, Z., The classification of the drift risk of sprays produced by spinning discs based on wind tunnel measurements (2008) Biosyst. Eng., 100, pp. 38-43
Rioboo, R., Voué, M., Vaillant, A., De Coninck, J., Drop impact on porous superhydrophobic polymer surfaces (2008) Langmuir, 24, pp. 14074-14077
Skuterud, R., Nordby, A., Tyldum, A., Effects of application methods, spray volumes, pressures and herbicide rates on weed control in spring cereals (1988) Crop Prot., 7, pp. 303-308
Solie, J.B., Alimardani, R., Predicting spray patterns of a vertical rotary disc atomizer (1986) Trans. ASAE, 29 (5), pp. 1193-1198
Southcombe, E.S.E., The international (BCPC) spray classification system including a drift potential factor (1997) Proceedings of the 1997 Brighton Crop Protection Conference - Weeds, pp. 371-380. , 17-20 November 1997, Brighton Centre and Stakis Brighton Metropole Hotel, Brighton, UK. British Crop Protection Enterprises
Taylor, P., The wetting of leaf surfaces (2011) Curr. Opin. Colloid Interface Sci., 16, pp. 326-334
Taylor, W.A., Controlled droplet application of herbicides (1981) Outlook Agric., 10, pp. 333-336
Van De Zande, J.C., Holterman, H.J., Porskamp, H.A.J., Influence of reference nozzle choice on spray drift classification (2002) Proceedings of the International Advances in Pesticide Application: Aspects of Applied Biology 66, 66, pp. 49-55. , 7-9 January 2002, University of Surrey, Guildford, UK. Warwick, UK: Association of Applied Biologists
Walton, W.H., Prewett, W.C., The production of sprays and mists of uniform drop size by means of spinning disc type sprayers (1949) Proc. Phys. Soc. London, Sect. B, 62, 341p
Wolf, T.M., Harrison, S.K., Hall, F.R., Cooper, J., Optimizing postemergence herbicide deposition and efficacy through application variables in no-till systems (2000) Weed Sci., 48, pp. 761-768
Zabkiewicz, J.A., Spray formulation efficacy-holistic and futuristic perspectives (2007) Crop Prot., 26, pp. 312-319
Zainoun, N., Chicheportiche, J.-M., Renaudeaux, J.-P., Contrôle dimensionnel des aérosols par piézoélectricité (2004) Gamac éditeur, pp. 169-177