[en] Bulk alumina foams were generated by slip casting of suspensions combined with particle-stabilized emulsion droplets as pore templates. Because of the volatile nature of the template, the green foams could be consolidated by sintering without a debinding step. The porous structure of the consolidated foams was analyzed nondestructively using image analysis of microfocus computer tomography (micro-CT) data. The fraction of open and closed pores, as well as the pore sizes and pore size distributions, were calculated from the generated 3D micro-CT datasets and correlated to the applied processing parameters. The anisotropy in the produced structures was assessed and elucidated by a detailed analysis of segmented tomography data. The results indicate that the width of the pore size distribution and the average macropore size, ranging from 225 to 136 mu m, depend on the slip rheology. Any anisotropy caused in the structure was linked to the template preparation but is only present in a narrow zone near the bottom of the foams. Although the macroporosity (>= 20 mu m) was only 24%-31%, tomographic analysis showed that over 90% of these macropores were interconnected through >= 20-mu m-diameter windows.
Disciplines :
Materials science & engineering
Author, co-author :
Neirinck, Bram; Katholieke Univ Leuven, Dept Met & Mat Engn MTM, B-3001 Heverlee, Belgium.
Kerckhofs, Greet ; Université de Liège - ULiège > Département d'aérospatiale et mécanique > Génie biomécanique
Wevers, Martine; Katholieke Univ Leuven, Dept Met & Mat Engn MTM, B-3001 Heverlee, Belgium.
Van der Biest, Omer; Katholieke Univ Leuven, Dept Met & Mat Engn MTM, B-3001 Heverlee, Belgium.
Vleugels, Jef; Katholieke Univ Leuven, Dept Met & Mat Engn MTM, B-3001 Heverlee, Belgium.
Language :
English
Title :
Morphological Analysis of Slip-Cast Emulsion-Templated Alumina Foams by Microfocus Computer Tomography
Publication date :
2010
Journal title :
Journal of the American Ceramic Society
ISSN :
0002-7820
Publisher :
Wiley-Blackwell, Malden, United States - Massachusetts
Volume :
93
Issue :
11
Pages :
3921-3928
Peer reviewed :
Peer Reviewed verified by ORBi
Funders :
IWT - Agentschap voor Innovatie door Wetenschap en Technologie [BE] KU Leuven - Catholic University of Leuven [BE]
Funding number :
Research Fund of K. U. Leuven [GOA/08/007, OT/08/028/TBA]
Commentary :
This work was supported by the Flemish Institute for the Promotion of Scientific and Technological Research in Industry (IWT) under grant SB/53092 and the Research Fund of K. U. Leuven under projects GOA/08/007 and OT/08/028/TBA.
J. Banhart, "Manufacture, Characterisation and Application of Cellular Metals and Metal Foams," Prog. Mater. Sci., 46 [6] 559-632 (2001).
B. Neirinck, J. Fransaer, O. Van der Biest, and, J. Vleugels, "Production of Porous Materials through Consolidation of Pickering Emulsions," Adv. Eng. Mater., 9 [1-2] 57-9 (2007).
B. Neirinck, J. Fransaer, O. Van der Biest, and, J. Vleugels, "Electrophoretic Deposition of Liquid Templates," Key Eng. Mater., 412, 299-305 (2009).
S. Barg, E. G. De Moraes, D. Koch, and, G. Grathwohl, "New Cellular Ceramics from High Alkane Phase Emulsified Suspensions (HAPES)," J. Eur. Ceram. Soc., 29 [12] 2439-46 (2009).
S. Barg, C. Soltmann, M. Andrade, D. Koch, and, G. Grathwohl, "Cellular Ceramics by Direct Foaming of Emulsified Ceramic Powder Suspensions," J. Am. Ceram. Soc., 91 [9] 2823-9 (2008).
U. T. Gonzenbach, A. R. Studart, E. Tervoort, and, L. J. Gauckler, "Ultrastable Particle-Stabilized Foams," Angew. Chem. Int. Edit., 45 [21] 3526-30 (2006).
I. Akartuna, A. R. Studart, E. Tervoort, U. T. Gonzenbach, and, L. J. Gauckler, "Stabilization of Oil-in-Water Emulsions by Colloidal Particles Modified with Short Amphiphiles," Langmuir, 24 [14] 7161-8 (2008).
S. U. Pickering, "Emulsions," J. Chem. Soc., 91, 2001-21 (1907).
R. Aveyard, B. P. Binks, and, J. H. Clint, "Emulsions Stabilised Solely by Colloidal Particles," Adv. Colloid Interface Sci., 100-102, 503-46 (2003).
L. J. Gibson, and, M. F. Ashby, Cellular Solids: Structure and Properties. Pergamon Press, Oxford, 1988.
S. Arditty, V. Schmitt, J. Giermanska-Kahn, and, F. Leal-Calderon, "Materials Based on Solid-Stabilized Emulsions," J. Colloid Interface Sci. 275 [2] 659-64 (2004).
C. W. Macosko, Rheology: Principles, Measurements and Applications. Wiley-VCH, New York, 1994.
L. A. Feldkamp, L. C. Davis, and, J. W. Kress, "Practical Cone-Beam Algorithm," J. Opt. Soc. Am. A-Opt. Image Sci. Vis., 1 [6] 612-9 (1984).
T. Hildebrand, and, P. Ruegsegger, "A New Method for the Model-Independent Assessment of Thickness in Three-Dimensional Images," J. Microsc.-Oxford, 185, 67-75 (1997).
E. Remy, and, E. Thiel, "Medial Axis for Chamfer Distances: Computing Look-Up Tables and Neighbourhoods in 2D or 3D," Pattern Recognit. Lett., 23 [6] 649-61 (2002).
E. Maire, P. Colombo, J. Adrien, L. Babout, and, L. Biasetto, "Characterization of the Morphology of Cellular Ceramics by 3D Image Processing of X-Ray Tomography," J. Eur. Ceram. Soc., 27 [4] 1973-81 (2007).
S. T. Ho, and, D. W. Hutmacher, "A Comparison of Micro CT with Other Techniques Used in the Characterization of Scaffolds," Biomaterials, 27 [8] 1362-76 (2006).
G. Kerckhofs, J. Schrooten, T. Van Cleynenbreugel, S. V. Lomov, and, M. Wevers, "Validation of X-Ray Microfocus Computed Tomography as an Imaging Tool for Porous Structures," Rev. Sci. Instrum., 79 [1] 013711, 9pp (2008).
J. Pan, H. N. Ch'ng, and, A. C. F. Cocks, "Sintering Kinetics of Large Pores," Mech. Mater. 37 [6] 705-21 (2005).
G. Kerckhofs, Morphological and Mechanical Quantification of Porous Structures by Means of Micro-CT. Department of Metallurgy and Materials Engineering, K. U. Leuven, Leuven, 2009.
T. Hildebrand, and, P. Ruegsegger, "Quantification of Bone Microarchitecture with the Structure Model Index," Comp. Meth. Biomech. Biomed. Eng., 1 [1] 15-23 (1997).
