  In vivo characterisation of a novel bioresorbable poly(lactide-co-glycolide) tubular foam scaffold for tissue engineering applications; ; et al in Journal of Materials Science: Materials in Medicine (2004), 15(6), 729-734 Polylactide-co-glycolide (PLGA) foams of tubular shape were assessed for their use as soft-tissue engineering scaffolds in vitro and in vivo. Porous membranes were fabricated by a thermally induced phase ... [more ▼] Polylactide-co-glycolide (PLGA) foams of tubular shape were assessed for their use as soft-tissue engineering scaffolds in vitro and in vivo. Porous membranes were fabricated by a thermally induced phase separation process of PLGA solutions in dimethylcarbonate. The parameters investigated were the PLGA concentration and the casting volume of solution. Membranes produced from 5 wt/v % polymer solutions and a 6 ml casting volume of polymer solution were selected for fabricating tubes of 3 mm diameter, 20 mm length and a nominal wall thickness of 1.5 mm. Scanning electron microscopy revealed that the structure of the tubularfoams consisted of radially oriented and highly interconnected pores with a large size distribution (50-300 µm). Selected tubes were implanted subcutaneously into adult male Lewis rats. Although the lumen of the tubes collapsed within one week of implantation, histological examination of the implanted scaffolds revealed that the foam tubes were well tolerated. Cellular infiltration into the foams, consisting mainly of fibrovascular tissue, was evident after two weeks and complete within eight weeks of implantation. The polymer was still evident in the scaffolds after eight weeks of implantation. The results from this study demonstrate that the PLGA tubular foams may be useful as soft-tissue engineering scaffolds with modification holding promise for the regeneration of tissues requiring a tubular shape scaffold such as intestine. [less ▲] Detailed reference viewed: 21 (0 ULg)Bioresorbable and bioactive composite materials based on polylactide foams filled with and coated by Bioglass (R) particles for tissue engineering applications; ; et al in Journal of Materials Science: Materials in Medicine (2003), 14(5), 443-450 Poly(DL-lactide) (PDLLA) foams and bioactive glass (Bioglass®) particles were used to form bioresorbable and bioactive composite scaffolds for applications in bone tissue engineering. A thermally induced ... [more ▼] Poly(DL-lactide) (PDLLA) foams and bioactive glass (Bioglass®) particles were used to form bioresorbable and bioactive composite scaffolds for applications in bone tissue engineering. A thermally induced phase separation process was applied to prepare highly porous PDLLA foams filled with 10wt% Bioglass® particles. Stable and homogeneous layers of Bioglass® particles on the surface of the PDLLA/Bioglass® composite foams as well as infiltration of Bioglass® particles throughout the porous network were achieved using a slurry-dipping technique. The quality of the bioactive glass coatings was reproducible in terms of thickness and microstructure. In vitro studies in simulated body fluid (SBF) were performed to study the formation of hydroxyapatite (HA) on the surface of the PDLLA/Bioglass® composites, as an indication of the bioactivity of the materials. Formation of the HA layer after immersion in SBF was confirmed by X-ray diffraction and Raman spectroscopy measurements. The rate of HA formation in Bioglass®-coated samples was higher than that observed in non-coated samples. SEM analysis showed that the HA layer thickness rapidly increased with increasing time in SBF in the Bioglass®-coated samples. The high bioactivity of the developed composites suggests that the materials are attractive for use as bioactive, resorbable scaffolds in bone tissue engineering. [less ▲] Detailed reference viewed: 43 (3 ULg)Novel bioresorbable and bioactive composites based on bioactive glass and polylactide foams for bone tissue engineering; ; et al in Journal of Materials Science: Materials in Medicine (2002), 13(12), 1207-1214 Bioresorbable and bioactive tissue engineering scaffolds based on bioactive glass (45S5 Bioglass®) particles and macroporous poly(DL-lactide) (PDLLA) foams were fabricated. A slurry dipping technique in ... [more ▼] Bioresorbable and bioactive tissue engineering scaffolds based on bioactive glass (45S5 Bioglass®) particles and macroporous poly(DL-lactide) (PDLLA) foams were fabricated. A slurry dipping technique in conjunction with pretreatment in ethanol was used to achieve reproducible and well adhering bioactive glass coatings of uniform thickness on the internal and external surfaces of the foams. In vitro studies in simulated body fluid (SBF) demonstrated rapid hydroxyapatite (HA) formation on the surface of the composites, indicating their bioactivity. For comparison, composite foams containing Bioglass® particles as filler for the polymer matrix (in concentration of up to 40 wt%) were prepared by freeze-drying, enabling homogenous glass particle distribution in the polymer matrix. The formation of HA on the composite surfaces after immersion in phosphate buffer saline (PBS) was investigated to confirm the bioactivity of the composites. Human osteoblasts (HOBs) were seeded onto as-fabricated PDLLA foams and onto PDLLA foams coated with Bioglass® particles to determine early cell attachment and spreading. Cells were observed to attach and spread on all surfaces after the first 90 min in culture. The results of this study indicate that the fabricated composite materials have potential as scaffolds for guided bone regeneration. (C) 2002 Kluwer Academic Publishers. [less ▲] Detailed reference viewed: 27 (2 ULg) |
||
