References of "Ly, Dong Phuong Lam"
     in
Bookmark and Share    
Full Text
Peer Reviewed
See detailNew simplified analytical method for the Prediction of global stability of steel and composite sway frames
Demonceau, Jean-François ULg; Ly, Dong Phuong Lam ULg; Coméliau, Ludivine ULg et al

in Proceedings of the annaual stability conference, 2010 (2010, May)

Eurocode 4 is the European design code for composite construction; in its so-called EN 1994-1-1 version, the design of “non-sway buildings” is mainly covered. As a result, EC4 focuses on the check of ... [more ▼]

Eurocode 4 is the European design code for composite construction; in its so-called EN 1994-1-1 version, the design of “non-sway buildings” is mainly covered. As a result, EC4 focuses on the check of structural elements like beams, columns, slabs and joints. However, in the last years, the construction of taller buildings and larger industrial halls without wind bracing systems tends to make global instability a relevant failure mode, which is not well covered by Eurocode 4. Recently, intensive experimental, numerical and theoretical investigations have been carried out at Liège University. The latter aimed at improving the knowledge in the field of sway composite building frames and at developing appropriate design rules. The rotational behavior of the beam-to-column composite joints is one of the key aspects of the problem to which a special attention has been paid. This paper reflects investigations carried out at Liege University on this topic. In particular, an innovative simplified analytical method to predict the ultimate loading factor and the associated collapse mode of both steel and composite frames subjected to static loadings is presented. [less ▲]

Detailed reference viewed: 105 (19 ULg)
Full Text
Peer Reviewed
See detailProposed design rules for iron columns reinforced by FRP
Ly, Dong Phuong Lam ULg; Demonceau, Jean-François ULg; Jaspart, Jean-Pierre ULg et al

in Mazzolani, F. M. (Ed.) Protection of historical buildings, Prohitech 09 (2009, June 21)

This paper presents design rules for iron columns under axial compression, strengthened with high modulus carbon fibre reinforced polymer (FRP) sheets. According to experimental and numerical results, it ... [more ▼]

This paper presents design rules for iron columns under axial compression, strengthened with high modulus carbon fibre reinforced polymer (FRP) sheets. According to experimental and numerical results, it is shown that the resistance and stiffness of iron columns can be significantly increased with the use of longitudinal FRP sheets because of the reduction of the column slenderness, but also that transverse FRP sheets should be used to prevent any local buckling of the longitudinal FRP sheets [less ▲]

Detailed reference viewed: 80 (20 ULg)
Full Text
Peer Reviewed
See detailExperimental and numerical investigations on iron columns reinforced by FRP under axial compression
Ly, Dong Phuong Lam ULg; Jaspart, Jean-Pierre ULg; Demonceau, Jean-François ULg et al

in Camelbeeck, Th.; Degée, Hervé; Degrande, G. (Eds.) et al Seismic risk (2008, September 11)

This paper presents experimental and numerical investigations on iron columns under axial compression, strengthened with high modulus carbon fibre reinforced polymer (FRP) sheets. It is shown that the ... [more ▼]

This paper presents experimental and numerical investigations on iron columns under axial compression, strengthened with high modulus carbon fibre reinforced polymer (FRP) sheets. It is shown that the resistance and stiffness of iron columns can be increased significantly with the use of longitudinal FRP sheets as a result of the reduction of the column slenderness, but also that transverse FRP sheets should be used to prevent any local buckling of the longitudinal FRP sheets. [less ▲]

Detailed reference viewed: 63 (9 ULg)
Full Text
Peer Reviewed
See detailNew simplified analytical method for the prediction of global stability of composite sway frames
Ly, Dong Phuong Lam ULg; Demonceau, Jean-François ULg; Jaspart, Jean-Pierre ULg

in EUROSTEEL 2008, 5th European Conference on Steel and Composite Structures (2008, September)

In the last years, the construction of taller composite buildings and larger composite industrial halls without wind bracing systems is susceptible to make global instability a relevant failure mode. This ... [more ▼]

In the last years, the construction of taller composite buildings and larger composite industrial halls without wind bracing systems is susceptible to make global instability a relevant failure mode. This one is not yet covered by EC4 [2]. This paper reflects investigations carried out of Liege University on this topic. In particular, an innovative simplified analytical method to predict the ultimate loading factor and the associated collapse mode of composite frames is derived. [less ▲]

Detailed reference viewed: 163 (9 ULg)
Full Text
See detailDevelopment of design rules for iron columns reinforced by FRP
Ly, Dong Phuong Lam ULg; Demonceau, Jean-François ULg; Jaspart, Jean-Pierre ULg

Report (2008)

In the available literature, some techniques of reinforcement are proposed: reinforcement with the use of cables, replacement of damage elements, creation of a composite action by connecting the damage ... [more ▼]

In the available literature, some techniques of reinforcement are proposed: reinforcement with the use of cables, replacement of damage elements, creation of a composite action by connecting the damage elements to a concrete slab, etc; but few of them are applicable to the Umberto 1 gallery. The one that seems to be applicable is the FRP (Fibre Reinforcement Polymer) technique. The behaviour of composite elements composed of FRP and steel members under tension seems to be known, but little information is available as far as the behaviour of such elements in compression. Following the "Iron meeting" held in Naples on June 8th, 2006, tests on stocky elements with and without FRP are planned to be performed in tension and in compression to identify the effect of FRP on such elements. In addition, tests on slender columns will be performed with and without FRP to investigate the influence of the latter on the buckling resistance. All the tests will be accompanied by coupon tests to identify the mechanical properties of the constitutive material of the tested specimens (Liège contribution to WP7). Based on the test campaign, analytical design rules founded on an elastic approach have been developed for the computation of the resistance of iron columns reinforced by FRP; these rules are detailed in the present section and reflect the contribution of the University of Liège to WP9. [less ▲]

Detailed reference viewed: 30 (6 ULg)
Full Text
See detailIron and FRP materials
Ly, Dong Phuong Lam ULg; Demonceau, Jean-François ULg; Jaspart, Jean-Pierre ULg

Report (2008)

Numerical investigations are very helpful to prepare and to plan experimental investigations. The numerical investigations presented within the present section deals with the experimental tests conducted ... [more ▼]

Numerical investigations are very helpful to prepare and to plan experimental investigations. The numerical investigations presented within the present section deals with the experimental tests conducted on iron elements reinforced by FRP in tension, i.e.: - first, to determine the anchorage length requested for the FRP (zone A of the figure 1.1 1) to insure a good stress transfer from the iron member to FRP sheets through bonds without any debonding problem; - and secondly, to predict the effects of FRP sheets on iron elements in tension. [less ▲]

Detailed reference viewed: 39 (4 ULg)
Full Text
See detailIron columns reinforced by FRP under axial compression
Ly, Dong Phuong Lam ULg; Jaspart, Jean-Pierre ULg; Demonceau, Jean-François ULg

Report (2008)

Slender iron column reinforced by FRP is sensitive to buckling phenomenon, taking place obviously at a cross-section within the middle segment. An equivalent FRP-iron cross-section can be used to derive ... [more ▼]

Slender iron column reinforced by FRP is sensitive to buckling phenomenon, taking place obviously at a cross-section within the middle segment. An equivalent FRP-iron cross-section can be used to derive the buckling resistance of the composite member by using buckling formulation previously defined for column members. [less ▲]

Detailed reference viewed: 30 (9 ULg)
Full Text
Peer Reviewed
See detailNumerical and analytical investigations on iron columns reinforced by FRP under axial compression
Ly, Dong Phuong Lam ULg; Rondal, Jacques ULg; Jaspart, Jean-Pierre ULg

in Smith, S. T. (Ed.) Asia-Pacific Conference on FRP in Structures-APFIS07 (2007, December)

This paper presents numerical and analytical investigations on iron columns under axial compression, strengthened with high modulus carbon fibre reinforced polymer (FRP) sheets. Numerical and analytical ... [more ▼]

This paper presents numerical and analytical investigations on iron columns under axial compression, strengthened with high modulus carbon fibre reinforced polymer (FRP) sheets. Numerical and analytical models are proposed to predict the resistance and stability load of such elements, including effects of section and member geometrical imperfections and of the nonlinear characteristic and the anisotropy in post elasticity of iron material. It is shown that axial resistance and stiffness of iron columns can be increased significantly with the use of longitudinal FRP sheets as a result of the reduction of the column slenderness, but also that transverse FRP sheets should also be used to avoid any local buckling of the longitudinal FRP sheets during loading. [less ▲]

Detailed reference viewed: 68 (3 ULg)
Full Text
See detailDéveloppement de modèles analytiques pour la prédiction du comportement élastique des assemblages mécaniques à broches dans la construction en bois
Ly, Dong Phuong Lam ULg

Doctoral thesis (2006)

A general procedure for the evaluation of the mechanical properties of structural joints, named “component method”, is now available from intensive research works at the European level. This procedure ... [more ▼]

A general procedure for the evaluation of the mechanical properties of structural joints, named “component method”, is now available from intensive research works at the European level. This procedure allows the analytical prediction of the resistance, but also of the stiffness and the deformation capacity, of structural joints under external forces (axial or shear forces, bending moments …). The component method is nowadays integrated as a reference procedure in two European de-sign codes, respectively for steel structures (EC3 [EN1993]) and steel-concrete composite structures (EC4 [EN1994]). However, its potential scope is much larger and present studies are aimed to apply to situations as joints in fire, joints under seismic loading, joints under exceptional loads (Robustness Project) …. More recently, a research project [CTI-2004] has succeeded in applying the component method to the investigation of the elastic behaviour of mechanical joints in timber construction. That is the result of the collaboration of CTIB-TCHN (Belgian Institute for Wood Technology) and University of Liège. The main principle of the component method is the following: • identification of constitutive components subjected to tension, compression or shear in the joint; • determination of the mechanical behaviour of these individual components; • "assembling" components so as to derive the mechanical properties of the whole joint. In the present paper, timber joints with dowel fasteners are considered. Two components may be identified: • "dowel" component (dowel fastener in bending and shear); • embedding component (timber member in embedding). The "dowel" component is known from past researches, whereas little information is available for the embedding component. EC5 [EN1995] proposes formulation to predict the behaviour for joints composed of these two components; but it only depends on two factors: the dowel diameter and the timber density. The influence probably significant of the grain direction (material strongly anisotropy) and the thickness of the connected members are for instance neglected. Experimental, numerical and analytical investigations have recently been performed by Uni-versity of Liège in collaboration with CTIB-TCHN so as to propose another formulation more precise for joints. Experimental results, performed by CTIB-TCHN, have been used as refer-ence for the development of numerical model and, then, analytical model. The application of the component method to the prediction of the elastic behaviour of timber joints consist of two steps: • "local" investigation on components that is to develop analytical models for the pre-diction of the elastic behaviour of components; • "global" investigation on joints that is to develop analytical models for the prediction of the elastic behaviour of joints. The application of the component method to timber joints with dowel fasteners is a first step towards the use of this concept in future to others mechanical joints (screw, punched metal plate, nail, bolt …). In this case, others components may be derived to cover the field of ap-plication expected. [less ▲]

Detailed reference viewed: 137 (12 ULg)
Full Text
Peer Reviewed
See detailApplication of the component method to structural joints with dowel fasteners in timber construction
Ly, Dong Phuong Lam ULg; François, N.; Mertens, A. et al

in Aoki, Tetsuhiko; Itoh, yoshito (Eds.) Proceedings of the first international conference on advances in experimental structural engineering (2005, July)

A general procedure for the evaluation of the mechanical properties of structural joints, named “component method” [01], is now available from intensive research works at the European level. This ... [more ▼]

A general procedure for the evaluation of the mechanical properties of structural joints, named “component method” [01], is now available from intensive research works at the European level. This procedure allows the analytical prediction of the resistance, but also of the stiffness and the deformation capacity, of structural joints under external forces (axial or shear forces, bending moments, …). In the present paper, timber joints with dowel fasteners are considered. Two components may be identified: the “dowel fastener in bending and shear” and the “timber member in embedding”. [less ▲]

Detailed reference viewed: 45 (1 ULg)
Full Text
See detailEssais de matériau de bois
Ly, Dong Phuong Lam ULg; Verstraete, Max ULg; Jaspart, Jean-Pierre ULg

Report (2004)

Tests caractéristiques du matériau bois dans le cadre de la recherche "Kser" avec la collaboration de CTIB (centre technique industriel du bois)

Detailed reference viewed: 68 (10 ULg)